Multisig using multiple hardware wallets is often used as a security upgrade for personal funds previously held in a single-signature wallet. In reality, it often achieves the opposite when it comes to remote attacks.
Combining hardware wallets from multiple vendors is a popular strategy to minimize the risk of a single point of failure, e.g. a serious vulnerability in one of involved wallets. Unfortunately, one weak hardware wallet can compromise the whole setup.
I work on the BitBox02 hardware wallet. Back when we first evaluated how to properly add multisig support, we stumbled across numerous pitfalls and security issues related to how people use hardware wallets to secure their coins in a multisig setup. Our blog post summarizing them is one of our most popular posts.
This post is an in-depth look at this small, but hugely important point of the original article:
Your hardware wallet should verify, or let you verify, the following information provided by the untrusted computer: [...]
* The xpubs of the cosigners in order to prevent an attacker from swapping them
The scope of this post is limited to setups where you use multiple hardware wallets and handle them using a single computer (or mobile phone).
My standard assumption is that your computer is already compromised. Hardware wallets' main value proposition is to protect against this. If your computer was safe to use, there would be little reason to use hardware wallets in the first place.
There are plenty of tutorials about how to set up multisig with hardware wallets. Due to the complicated nature of it, all of them either skip over xpub verification, cannot perform it due to a lack of hardware wallet support, or simply do it incorrectly. Any of those leave the door open for an attacker to do harm.
A quick recap: an xpub, short for extended public key, is used to derive all the addresses in an account. In the case of multisig, a threshold and one xpub per cosigner are combined to generate multisig addresses.
Let's first discuss what can go wrong if the xpubs are not verified properly.
After that, I will show that despite your best efforts, you likely will not have verified the xpubs properly if you used only one computer.
Hardware wallet users are well educated to ultimately trust the device screen. If the device screen shows something, it must be safe to use.
This does not hold true for multisig receive addresses.
A multisig address is derived from the multisig threshold and all cosigner xpubs. One hardware wallet can only silently verify its own xpub. The other xpubs are provided by the computer wallet, e.g. Electrum.
A compromised computer wallet can provide fake cosigner xpubs to the hardware wallet. For example, in a 2-of-3 multisig, the compromised wallet will provide two xpubs controlled by the attacker. After verifying the compromised receive address, any funds sent to it belong to the attacker.
A common security measure people do is to test the multisig setup first: receive a small amount, spend it and then, if it all worked, send in the big funds. Unfortunately, this cannot prevent this theft attack. A compromised computer can simulate the whole procedure of receiving and spending the test amount, including verification on all hardware wallets. More details on this in a future blog post.
Possible mitigations are:
- Comparing that the same address is shown on each cosigner wallet. This is often not feasible, e.g. in a 2-of-3 setup, the third device could be in a remote location.
- Proper xpub verification. I will get into why this is nearly impossible in a bit.
In a ransom attack, the attacker does not outright steal the coins, but controls your access to them. By locking you out of your coins, the attacker can negotiate a payout to release the funds back to you.
One simple example works exactly like the theft attack described above, but with a 2-of-2 multisig instead of a 2-of-3 multisig. If one xpub belongs to you, and one xpub belongs to the attacker, it requires the cooperation of both parties to release any coins sent to this account.
A more subtle attack exploits your backups.
In order to be able to restore a 2-of-3 multisig wallet, the threshold and all cosigner xpubs need to be known. It is best practice to store all of this information along with each cosigner backup. Then you can restore a wallet even if one cosigner seed is permanently lost or inaccessible by using the private keys of the other two cosigners and all three xpubs.
In all multisig tutorials and all multisig setups I have witnessed or reviewed, at best, the xpub backup was created by copying the xpubs as provided by the computer wallet (e.g. by copying them into a text file to be printed).
A compromised computer can at this point display fake xpubs. Even if only one xpub is incorrect, your backup is compromised.
If you ever find yourself in a situation where you need to restore your 2-of-3 multisig setup by using two out of three cosigner backups, you are in trouble. In theory, the two cosigner seeds and three xpubs backed up along with them should be sufficient to regain access to your funds. If however the xpubs in the backup are incorrect, you will not be able to recover. The wallet restored from this backup would be an empty, wrong wallet. The attacker is the only one that can help you recover.
In order to create valid backups, one must be sure that the xpubs printed on paper match the xpubs as shown on the hardware wallet screens. Depending on the hardware wallets involved, this is very hard or impossible to achieve, as we'll see in the next section.
Obstacles to xpub verification
Table of common obstacles. Each of the entries is explained in more detail below.
|Display own xpub on demand||✅||❌||❌||✅|
|Display cosigner xpubs||✅||❌||✅||✅|
|Register xpubs inside the device||✅||❌||❌||✅|
Display own xpub on demand
To ensure your backup of the xpubs is correct, you should verify the xpubs in your backup on the hardware wallet displays (one xpub per device). For example, when using a BitBox02 with Electrum, you can click the eye icon to verify the xpub on the BitBox02 display:
It is important to verify the xpub displayed on the hardware wallet against the physical printout, not against what is shown in the computer wallet.
As far as I know, only the BitBox02 and Coldcard provide this function. In the Coldcard, it possible like this: Go to
Advanced -> View Identity. Make a note of the master key fingerprint. Then in
Settings -> Multisig Wallets -> <wallet> -> View Details, you can find the Coldcard's xpub below the device fingerprint.
Display cosigner xpubs
When verifying a receive address on one device, it can only be trusted if the xpubs that make up the address also are verified on the device. BitBox02:
The Ledger does not currently have the ability to display its own or any cosigner xpub.
Last year I responsibly disclosed the issue of possible theft/ransom attacks due to missing xpub verification to SatoshiLabs. Following this, the Trezor gained the ability to verify the xpubs by clicking on
QR and then on
XPUBs when verifying a receive address:
Problematic is that the xpubs are hidden behind the QR-code, which in my opinion is not discoverable. I fear that due to this, next to no Trezor user makes use of this important feature.
The Coldcard shows them during the setup of a multisig account.
The big issue in general is that it is not clear what to compare the xpubs against. Let's say you have a Trezor, a Ledger and a Coldcard in a multisig setup. All three xpubs are shown by the Trezor. How to verify them?
- You cannot verify them against what the computer wallet shows, as that can be fake (see the previous section "Display own xpub on demand").
- You would need to verify them against a trusted physical copy of the xpubs every time you verify a receive address. Making such a trusted copy is extremely difficult or impossible, as the xpubs cannot be shown at the right time on all hardware wallets.
- Ledger does not show its own xpub nor any cosigner xpub, so the Ledger xpub cannot be verified, period.
Show Electrum Zpub... and Ypub... formats
This issue appears when using the popular Electrum wallet or any compatible wallet. Electrum encodes xpubs differently depending on the account type. For example, native segwit multisig account xpubs are formatted as
Zpub..., while wrapped segwit multisig xpubs are formatted as
Ypub.... See the full table here.
While all the different formats encode the same extended public key, they look completely different. For example:
encodes the same xpub as:
You cannot manually verify that they are the same, it is not only a matter of swapping the four letter prefix.
If a hardware wallet does not support these formats, verifying xpubs in Electrum is impossible, even for wallets like Trezor and Coldcard which are able to show xpubs on their screens otherwise. The Coldcard even exports the xpubs in the right formats (
Zpub...) to the microSD card, but only shows
xpub... when verifying them.
One could use an xpub converter to convert
Zpub... into an
xpub... before verification. This is not failsafe of course, as a compromised computer can modify the result.
To my knowledge, only the BitBox02 is able to display the xpubs in the format required by the computer wallet:
Electrum is probably the most widely used multisig wallet today, so it is important to properly support these xpubs formats. Some are of the opinion they will be obsolete as descriptor-based wallets become adopted. This however can take a very long time, and we should not wait for it.
Register xpubs inside the device
Registration of the multisig configuration means that you only have to verify the xpubs once. The device remembers the verification. After that, you can safely verify receive addresses without worrying about the cosigner xpubs.
The BitBox02 lets you verify and register the xpubs and give the account a name. When verifying a receive address, the name is displayed, and you can be sure that the address indeed belongs to the account you created and verified at the start.
The Coldcard works the same way, minus the account name.
The Ledger does not verify nor register any multisig data.
While the Trezor can show the cosigner xpubs when verifying a receive address, it does not register them. This means that you have to diligently verify all cosigner xpubs against a trusted physical copy every time you generate a receive address. The previous section goes into the difficulties of doing that. In particular, verifying the xpubs against what the computer wallet displays is no good, as those can be fake.
Conclusion and recommendations
Multisig is hard. Almost one year after the pitfalls of multisig article was released, my conclusion is still the same: verification, backup and UX pitfalls might very well mean that multisig is less secure in practice than single-signature. Still too many footguns exist in the setup, use and backup/recovery of multisig wallets.
One of these footguns is the lack of cosigner xpub verification. The most pressing issue is the inability to verify the xpub of a device on demand, which can lead to remote theft or ransom attacks. I urge all hardware wallet vendors to implement this functionality and to expose it in multisig wallets like Electrum, in order to reduce the difficulty of properly verifying the xpubs.
If you insist on combining hardware wallets of multiple vendors, I recommend to verify each receive address on all hardware wallets, every time. This rules out Ledger, as the Ledger does not seem to be able to show a multisig receive address for verification. Furthermore, I recommend to test backup and recovery on a separate, independent computer.
Originally published at https://benma.github.com.
Swiss made 🇨🇭 security
We are the makers of the BitBox02 hardware wallet. Its secure dual-chip architecture reflects our values as a Swiss open-source security company: it enables the use of a secure chip for physical device hardening in combination with fully open-source firmware. Made in Switzerland, it inherits our deep appreciation of quality and privacy.
Learn more about potential threats to hardware wallets and how we prevent them in our extensive BitBox02 threat model.
The BitBox02 comes in two editions: the Multi edition that supports multiple crypto assets and can be used as a second-factor authenticator. And the Bitcoin-only edition, which features a radically focused firmware: less code means less attack surface which further improves your security when only storing Bitcoin.
Discover the BitBox02 and get one today, we ship worldwide!
Shift Crypto is a privately held company based in Zurich, Switzerland. Our international team of specialists across engineering, cryptosecurity and Bitcoin core development build the BitBox products and provide consulting services. The BitBox02, a second generation hardware wallet, equips individuals to easily store, protect, and transact cryptocurrencies. Its companion, the BitBoxApp, provides an all-in-one solution to securely manage your digital assets with ease.